防爆接线盒 Explosion Proof Junction Box | | | Brief Introduction of Product | | - 增安型防爆接线盒符合GB83836.3-2000的防爆规定,在II类1区和2区防爆场所供并联带安装用。
Incremental safety explosion proof junction box complies with the requirements specified in G83836.3-2000.This is applied in Zone 2, Grade II, for parallel connection cable purpose. | - 隔爆型防爆接线盒符合GB83836.2-2000的防爆规定,在II类1区和2区防爆场所供串联带安装用。
Flameproof enclosure junction box complies with the requirements specified in G83836.3-2000. This is applied in Zone 1,2, Grade II, for series connection cable purpose. | | Product Technical Parameters | 名称 | 电源接线盒 Power Junction Box | | 二通接线盒 Two-way Junction Box | | 三通接线盒 Three-way Junction Box | | 终端接 线盒 Terminal Junction Box | | 热电阻 接线盒 Thermal resistance Junction Box | | 隔爆型接线盒 Flameproof Enclisure Junction Box | | 项目 | 型号 | BHR81A- 15D/3 | BHR81A- 15Z/2 | BHR81A- 15Z/3 | BHR81A- 15F/1 | BHR81- 15R/3 | BHR85- 60 | 额定电压 | 220V/380V | 220V-660V | 额定电流 | 15A | 60A | 绝缘电阻 Insulation Resistance | | ≥50MΩ | ≥50MΩ | 防护等级 Ingress protection | | 1P56 | IP56 | 外形尺寸 | 178*60*57 | 135*60*35 | 135*77*35 | 45*20*51 | 178*60*57 | 230*190*120 | 防爆标志 Explosion Proof Label | | ExeIIBT4 | 用途 | 电源电缆与并 联带的连接 Connection between powercable and parallel connection cable | | 两根并联带 之间的连接 Connection between two parallel connection cables | | 三根并联带 之间的连接 Connection between three parallel connection cables | | 并联带的 尾端密封 End sealing of parallel connection cables | | 热电阻与控 制电缆连接 Connection between thermalresist- ance and con- trol cable | | 串联带与电缆 /串联带连接 和尾端密封 connection between series cables and power cables, series cables/connec-tion and End Sealing | | 3.并联带用防爆接线盒安装示意图 | Installing Sketch of Explosion proof Junction Box for Paralles connection cable | | Points to Be Noticed for Product Installation | | (1)发现接线盒外壳有变形、裂痕和损坏、应停止使用。 | | Where there is distortion,crack or damage on the junction box,it must be stopped using. | | (2)安装时应防止电热丝和外编织铜丝及芯线之间的短路。 | | When installing,avoid any short circuits between electric heating wires, braided copper wires and core wires. | | (3)应按电热带的型号选用所附适当的密封圈。 | | Choose proper sealing rings according to the types of electric heating cables | 电伴热带系列 >> 电伴热电气附件 >> 防爆温度控制器 | | | | 产品编号: | | 产品名称: | 防爆温度控制器 | 规 格: | | 产品备注: | | 产品类别: | 电伴热带系列 | | | | | 防爆温度控制器 Explosion Proof Temperature Controller | | | General Description | 防爆温度控制器符合GB3836.2-2000的防爆规定,防爆标志为ExdIIBT4。在 II 类一区、二区危险场所供温控器与电伴热带配套使用,用于自动控制管线或罐体温度。 The explosion proof temperature controller complies with the requirements specified in G83836.2 … 2000. The explosion proof mark is Exd II BT4.The temperature controller is used combined with electric heating cable in Zone 1, 2,Grade II. It is applied to controlling temperature automatically of pipes or tanks. | | | | | Product Main Technical Parameters | 型号 | 额定电压 | 额定电流 | 控温范围 Temperature Control Rage | | 控温精度 Precision of Temperature Control | | 通断差动 Connection and Break Differential | | 防护等级 Ingress Protection | | BJW82A-120/15 | 220/380V | 15A | 10-120℃ | ±2.5℃ | ≤4℃ | IP56 | BJW84A-120/15 | 220/380V | 15A | 50-200℃ | ±3℃ | ≤4℃ | IP56 | Product Working Principle and Installation | | 温控器中感温包接触到的被控介质温度升高时,感温包中的液体受热膨胀,当被控介质超过设定温度时,触点断开,系统自动切断电源、停止伴热。此时,感温包温度慢慢降低,被控温度低于设定温度时触点重新闭合,又自动恢复送电。 | | The temperature sensor in temperature controller feels the temperature 0fthe controlled media increases, the liquid in the tensor swells. When the temperature 0fthe media exceeds the set point, the connecting point will separate, and then the power will be switched off and the heating stopped, And then the temperature decline slowly,ifbelow the set point, the connecting point will connect again and power connection is recovered, | | 温控器安装时感温包只能水平安装和垂直向下安装,否则会出现温度不稳定现象。 | | When installing temperature controller,temperature sensor shall be put horizontally and vertically,Otherwise the temperature is unstable | | 先检查温控器通、断正常后,才能安装。 | | Install only after check the connection and break of temperature controller is normal | | 电伴热带系列 >> 电热带安装辅件 >> 铝胶带 | | | | 产品编号: | | 产品名称: | 铝胶带 | 规 格: | | 产品备注: | | 产品类别: | 电伴热带系列 | | | | | 铝胶带为厚0.06mm、宽50mm的铝箔带基上涂覆一层特殊的胶粘剂,每卷50米。它主要用于固定电热带和温控器的感温包,增大散热面,提高传热效果。 | The tape is aluminum sheet,with thickness 0.06mm and width 50mm and length 50m per roll,and with special adhesive gulue on base.It is mainly used for fixing electric heating cable and temperature sensor,to expanding heat conducting area and enhance heat transmitting effect. | | 电伴热带系列 >> 电热带安装辅件 >> 耐热胶带 | | | | 产品编号: | | 产品名称: | 耐热胶带 | 规 格: | | 产品备注: | | 产品类别: | 电伴热带系列 | | | | | 耐热胶带为厚 0.2mm 、宽 20mm 的玻璃纤维带基上涂覆一层特殊的胶粘剂,每卷20米。电热带用铝胶带安装后,沿管道径向每隔0.6m用该胶带再次固定牢。一般每个点应缠绕4/3圈。 This adhesive tape is a kind of glass fiber with special adhesive,with thickness 0.2mm and width 20mm and length 20m per roll.After the electric heating cable is installed with aluminum adhesive tape,the tape is used radially along the pipe to fix cable tightly in every 0.6m interval.Every point shall be wound 4/3 circles. | | 电伴热带系列 >> 电热带安装辅件 >> 管卡 | | | | 产品编号: | | 产品名称: | 管卡 | 规 格: | | 产品备注: | | 产品类别: | 电伴热带系列 | | | | | 管卡由不锈钢带和调节螺丝组成,用它将防爆接线盒或温控器固定在管道上。安装前,先按实际长度放长20mm后剪下钢带,再将调节螺丝放在钢带二头的小孔内,然后拧紧调节螺丝。 Pipe screw is consisted of stainless steel belt and adjusting bolt.It is used to fix explosion proof junction box or temperature controller to pipes.Before installing,cut steel belt according to actual length plus 20mm,then put the bolt in small holes and tighten the bolts. | | | | | | |